
IMI CCI
Specialist control valve solutions for general and severe service conditions
Core Technology
We care about your critical equipment and IMI CCI is served to handle severe service application. The core Technologies for severe service (high pressure drop) application focused on:
Tortuous path design

Splits a single large fluid jet or stream into numerous smaller streams that pass through a series of right-angled turns and friction stages.
Multi-stage & Multi-path design

Breaking down a massive pressure drop into smaller to eliminate cavitation, minimize erosion and reduce Noise & Vibration.
Exit Trim Velocity

Limit trim exit velocity below 23 m/s (75 ft/s) as per ISA guideline.
Growth Hub
To navigate and face the growing challenges in the market, IMI CCI Growth Hub is present as solution to finding customer problems, testing solutions early, stopping what doesn't work and scaling what does.
IMI Retrofit3D (R3D)
IMI Retrofit3D (R3D) is a specialized engineering solution developed by IMI plc that utilizes state-of-the-art additive manufacturing (3D printing). Instead of replacing a complete set valve—which requires expensive capital expenditure, pipe cutting, re-welding, and extensive downtime—Retrofit3D engineers custom drop-in internal parts (trims, seats, plugs, and disk stacks) that fit perfectly inside the existing valve body.

IMI Retrofit3D (R3D) success replacement of 2 Set BFP Minimum Flow (Deaerator Recirculation) Control Valve in Cirebon Power Plant. Existing (competitor) issues were leak and erosion causing the poor performance of line feed water which is impact on plant efficiency.
1st replacement is successfully done in 2024. Less than a year, considering another existing competitor condition which is leakage around 150 -200 ton/hr and estimate within 2.5 - 3 years will be ROI and in 6 months (by not waiting until 1 years on 1st replacement) customer seeing the benefit by just implementing the 1st success story repeat order to the next unit.

This success story proved that CCI product is the best solution for the most critical/severe service application in power plant.
Strong technical convince, deep discussion with IMI CCI expert and good communication between IMI, Agent and End user lead to sweet result.
IMI Erosolve Wet Steam (EWS)

IMI Erosolve Wet Steam (EWS) is custom-engineered valve trim components configured to extend the operational life of valves operating under harsh, wet steam erosion environments. Especially for Steam Conditioning Valve and HP/LP Bypass Application.


IMI CCI and PT KEI success installed EWS upgrade in Tanjung Jati 3&4 LP Bypass Valve since 2024 and perform very well until now.
Existing issue were leak and trim erosion. The pattern on plug and seat from the report last overhaul indicates that erosion has occurred caused by wet steam.
“We are happy with the support from PT KEI & IMI Critical Engineering (CCI) from the start of investigating issue until expedite the lead time. We hope that EWS can solve the issue that we are facing and increase valve performance & plant efficiency”
IMI EroSolve Flashing (ESF)

IMI EroSolve Flashing (ESF) provides an ultimate flashing solution configured to reduce valve erosion caused by flashing while maximising the valve performance against the given conditions. EroSolve Flashing product line is available in both Angle and Globe configuration.
Success story for replacement CBD application to IMI EroSolve Flashing solution in Paiton Unit 9 Power Plant. After many repaired on valve existing and still always leak in the time of 3-4 months, customer decided to replaced brand new valve of existing again (assuming the new valve will solve the issue). But in the time of 1.5 to 2 years leak and few repaired were perform and still leak. Engaged and convince customer with EroSolve solution on this issue.

IMI Solution is ensure dirt and particle on the CBD application need to be cater while also need to perform velocity control due to high DP. And with the small-bore size and multi-stages required Pintel DRAG was utilized.
IMI Long Serviceable Trim (LST)
IMI Long Serviceable Trim (LST) is specially designed to solve cavitation issues at minimum flow control.

Typical applications - Power plants
- HP Turbine Bypass TCV
- Attemperator TCV
- Process Desuperheater TCV
- CRH to Aux Steam TCV
- Feedwater Control Valve
- Drum Level Control Valve
- High rangeability requirement

Key features and benefits
- Enhanced plug design with an added nose
- Labyrinth grooves on the plug
- Protection of seating surface
- Gap control mechanism
- Full open control
IMI Insyt
IMI Insyt is engineering service a cloud-based diagnostic and predictive maintenance platform.
It leverages plant data to predict component failure modes, calibrate system interactions, and optimize plant flow control before downtime occurs.

Product Lines
- IMI CCI Drag : 100DR, 100D, 100DSV, 100H, 900D, etc.
- IMI CCI ABJ (formerly known as Gadelius or CCI K.K) : AB100, AB300, AB200, AB6300, etc.
- IMI CCI 840 Series : 840H, 840G, 840-3D, 840-ESF, etc.
- IMI CCI Sulzer : IMI CCI DRE, IMI CCI NBSE, IMI CCI HBSE, etc.
- IMI CCI BTG for Turbine Bypass Application
- IMI CCI STI for Actuator and Damper Applications
- IMI B&R for Turbine Bypass Application
- IMI CCI FLUID KINETIC for Silencer

Inquiry
A severe service problem you have not solved yet?
Send us the duty — medium, pressure drop, temperature and line size — and we will come back with the IMI CCI technology that fits.
